StainSoak™ eliminates pre-treatmentThe StainSoak option customizes your wash cycle, time, and temperature to eliminate common stains that need specific treatment—chocolate, blood, or any stain. Plus, SmartBoost™ technology pre-mixes water, detergent and stain remover to maximize their cleaning power, so there’s no need to pre-treat ahead of time. When choosing a water temperature, these are the basic points to consider:. Hot water cleans most effectively, but it shouldn’t be used for all items.
Warm water can be used for most normally soiled loads. Cold water is recommended for lightly soiled or brightly colored or dark items.To compensate for a cooler wash, it may be necessary to soak or prewash heavily soiled items, increase wash time or use additional laundry products to boost the detergent’s cleaning power.To protect your fabrics, not all temperatures are available with every cycle. If a temperature is not appropriate for the cycle, it cannot be selected. Your Electrolux Front Load Washer is smart. It will remember the temperature you select for a cycle and recall it each time until you change it.
Based on your detergent choice, here are some helpful tips:Liquid: Add the recommended amount of a high efficiency liquid detergent to the Main Wash – Liquid Only cup. Do not exceed the MAX fill line.Powder: To use a high efficiency powder detergent, remove the Main Wash – Liquid Only cup and add the powder directly to the Main Wash detergent chamber. It’s important to save the liquid cup insert in case you need it for future use.Pods: Place the pod directly into the washer drum BEFORE placing laundry into the unit. Electrolux recommends using a high-efficiency (HE) detergent for front load washers. HE detergents are designed for front load washers which use lower water levels.
Zanussi 6kg 900rpm-1000rpm Top Loading ZWQ590SO / ZWQ7100SO Washing. Eco Valve Delay Start Prewash Eco Easy Iron Super Quick Rinse Hold. Electrolux Inspire 6kg Eco Valve - Washing machine. How to replace Electrolux washing machine door seal 2012 onwards - Duration: 12:38. Content of the material:. Electrolux program table: description and symbols It is not recommended to select a specific mode at random. It is better to immediately read the description of the.
They are also formulated to reduce soap suds and ensure proper cleaning.Non-HE detergents may cause excessive generation of soap suds and result in detergent residue on your clothing at the end of the cycle. Always refer to your detergent manufacturer instructions for the proper dosage. Do not fill any compartments in your dispenser beyond the maximum amount line.We do not recommend the use of detergent pods with our front load washers.
We are unable to guarantee the pod will dissolve at the correct time during the wash cycle to ensure proper cleaning performance. If pods are used, please place the pod directly into the washer drum BEFORE placing laundry into the unit. Do not place the pod in the detergent drawer as the gel coating may cause the detergent drawer to become clogged. For optimal care refer to the guidelines in your Owner’s Manual. However, here are some quick tips:. Promptly remove finished loads.
Clean the top and sides of the washer with a damp cloth or mild soap and water. Avoid hard, gritty or abrasive cleansers. Leave door open to keep washer fresh when not in use.Some models have a feature that props the door open when the washer is not in use. When washing heavily soiled items, shake or brush off excess dirt and sand before putting them in the washer.
If any dirt remains in the drum after washing, wipe with a non-abrasive cleaner, then rinse.Most models have a System Clean Cycle or Clean Washer Cycle and will automatically prompt you to run the cycle every 50 wash cycles. StainTreat II™ Option removes set-in stainsOptimizes temperature, tumbling actions, and cycle time for enhanced stain-removing conditions based on the stain you select – chocolate, blood or any stain. When choosing a water temperature, these are the basic points to consider:.
Hot water cleans most effectively, but it shouldn’t be used for all items. Warm water can be used for most normally soiled loads. Cold water is recommended for lightly soiled or brightly colored or dark items.To compensate for a cooler wash, it may be necessary to soak or prewash heavily soiled items, increase wash time or use additional laundry products to boost the detergent’s cleaning power.To protect your fabrics, not all temperatures are available with every cycle. If a temperature is not appropriate for the cycle, it cannot be selected. Your Electrolux Front Load Washer is smart. It will remember the temperature you select for a cycle and recall it each time until you change it.
Based on your detergent choice, here are some helpful tips:Liquid: Add the recommended amount of a high efficiency liquid detergent to the Main Wash – Liquid Only cup. Do not exceed the MAX fill line.Powder: To use a high efficiency powder detergent, remove the Main Wash – Liquid Only cup and add the powder directly to the Main Wash detergent chamber. It’s important to save the liquid cup insert in case you need it for future use.Pods: Place the pod directly into the washer drum BEFORE placing laundry into the unit. Electrolux recommends using a high-efficiency (HE) detergent for front load washers.
HE detergents are designed for front load washers which use lower water levels. They are also formulated to reduce soap suds and ensure proper cleaning.Non-HE detergents may cause excessive generation of soap suds and result in detergent residue on your clothing at the end of the cycle. Always refer to your detergent manufacturer instructions for the proper dosage. Do not fill any compartments in your dispenser beyond the maximum amount line.We do not recommend the use of detergent pods with our front load washers. We are unable to guarantee the pod will dissolve at the correct time during the wash cycle to ensure proper cleaning performance. If pods are used, please place the pod directly into the washer drum BEFORE placing laundry into the unit. Do not place the pod in the detergent drawer as the gel coating may cause the detergent drawer to become clogged.
For optimal care refer to the guidelines in your Owner’s Manual. However, here are some quick tips:. Promptly remove finished loads.
Clean the top and sides of the washer with a damp cloth or mild soap and water. Avoid hard, gritty or abrasive cleansers. Leave door open to keep washer fresh when not in use.Some models have a feature that props the door open when the washer is not in use. When washing heavily soiled items, shake or brush off excess dirt and sand before putting them in the washer. If any dirt remains in the drum after washing, wipe with a non-abrasive cleaner, then rinse.Most models have a System Clean Cycle or Clean Washer Cycle and will automatically prompt you to run the cycle every 50 wash cycles. When choosing a water temperature, these are the basic points to consider:.
Hot water cleans most effectively, but it shouldn’t be used for all items. Warm water can be used for most normally soiled loads. Cold water is recommended for lightly soiled or brightly colored or dark items.To compensate for a cooler wash, it may be necessary to soak or prewash heavily soiled items, increase wash time or use additional laundry products to boost the detergent’s cleaning power.To protect your fabrics, not all temperatures are available with every cycle.
If a temperature is not appropriate for the cycle, it cannot be selected. Your Electrolux Front Load Washer is smart. It will remember the temperature you select for a cycle and recall it each time until you change it.
Based on your detergent choice, here are some helpful tips:Liquid: Add the recommended amount of a high efficiency liquid detergent to the Main Wash – Liquid Only cup. Do not exceed the MAX fill line.Powder: To use a high efficiency powder detergent, remove the Main Wash – Liquid Only cup and add the powder directly to the Main Wash detergent chamber. It’s important to save the liquid cup insert in case you need it for future use.Pods: Place the pod directly into the washer drum BEFORE placing laundry into the unit. Electrolux recommends using a high-efficiency (HE) detergent for front load washers. HE detergents are designed for front load washers which use lower water levels. They are also formulated to reduce soap suds and ensure proper cleaning.Non-HE detergents may cause excessive generation of soap suds and result in detergent residue on your clothing at the end of the cycle. Always refer to your detergent manufacturer instructions for the proper dosage.
Do not fill any compartments in your dispenser beyond the maximum amount line.We do not recommend the use of detergent pods with our front load washers. We are unable to guarantee the pod will dissolve at the correct time during the wash cycle to ensure proper cleaning performance. If pods are used, please place the pod directly into the washer drum BEFORE placing laundry into the unit. Do not place the pod in the detergent drawer as the gel coating may cause the detergent drawer to become clogged. For optimal care refer to the guidelines in your Owner’s Manual. However, here are some quick tips:. Promptly remove finished loads.
Clean the top and sides of the washer with a damp cloth or mild soap and water. Avoid hard, gritty or abrasive cleansers. Leave door open to keep washer fresh when not in use.Some models have a feature that props the door open when the washer is not in use. When washing heavily soiled items, shake or brush off excess dirt and sand before putting them in the washer. If any dirt remains in the drum after washing, wipe with a non-abrasive cleaner, then rinse.Most models have a System Clean Cycle or Clean Washer Cycle and will automatically prompt you to run the cycle every 50 wash cycles.
Electrolux basic washer error codesOne of the world’s leaders in household appliances, Electrolux manufactures a diverse range of washing machines. Electrolux basic washers are reliable and efficient, while the newer models offer a number of advanced options, like Fast Wash, LuxCare, and Perfect Steam.CodeProblemPossible CauseRemedyFault code E10 appears. The display RINSE + flashesNo water flowsWater tap is closed.Open the water tap.Filter in screw connection of the inlet hose is blocked.Close the water tap. Unscrew the hose from the tap, remove the filter and clean under running waterWater tap is blocked with limescale or is faultyCheck the water tap and have it repaired if necessary.The fault code E20 appears. The RINSE display flashes.The washing is not sufficiently spun. Water is left in the drum.Drain hose is kinked.Remove the kink.Maximum pump head (discharge height 1m from the appliance's base) is exceeded.Contact your local Service Force Centre. For pumping heights over 1m a conversion kit is available as a special accessory.Drain pump is blocked.Switch off the appliance and pull out the mains plug.
Clean the drain pumpThe fault code E40 appears. The display MAIN WASH flashesThe door is not correctly closed.Close the door correctly. Start the programme again. Electrolux EWFM series, AWF series washer error codesElectrolux EWFM is a series of front-loading washing machines with low water, energy and detergent consumption.
A drying board and an extractable shelf are some of their characteristic features. Electrolux IQ-Touch Wave-Touch EIFLW series washer error codesFront-load washers from the EIFLW series are equipped with the IQ-Touch control panel, which shows you all the details of the washing program you have chosen. This series includes washing machines with a Touch-2-open cycle selector, a dispenser drawer, and a door latch with safety lock.Error CodeFault ConditionCheckCorrectionE11Fill time too long.1. Is the incoming water flow normal?Yes. Go to step (4).No.
Go to step (2)2. Are the incoming water faucets turned on?No. Turn water faucets on.Yes. Go to step (3).3. Is the incoming water pressure above (20) psi.No. Have customer correct pressure problem. Check for kinked or blocked incoming water hoses, clean the incoming water screens.
If problem still remains, replace the water inlet valve assembly.4. Does the fill water continue to enter the washer?Yes. Go to step (5).No. Go to step (6)5. Remove power from the washer.Did the water fill stop?Yes. Go to step (6)No. Replace the inlet valve assembly.
Pressure switch checks good. Go to step (7).
Pressure switch checks bad. Replace the pressure switch.6. Replace the pressure sensorIf this did not correct the problem, go to step 7.7. Replace the main control board.E13Water leak in tub or air leak in air bell.1. Is the washer leaking water?Yes. Correct water leak.No.
Go to step (2)2. Is there an air leak in the air bell system?Yes. Correct the air leak problem.No.
Go to step (3)3. Replace the pressure sensorIf this did not correct the problem, Go to step (4)4. Replace the main control board.E21Water not pumping out fast enough.1. Check the drain hose for restrictions.Restriction. Correct problem.No restriction. Go to step (2).2. Start the washer and check for 120 VAC atthe drain pump.Zero.
![Eco Eco](/uploads/1/2/5/3/125371985/260733047.jpg)
Check the wiring. If wiring good, replace the main control board.120 VAC. Remove the pump and check for blockage. If blocked, remove the restriction, if not, replace the pump.E31Electronic pressure switch failure.Inspect the wiring between the pressuremain control board.Defective wiring.
Correct wiring.Good wiring. Replace the pressure sensor. If this does not correct the problem, replace the main control board.E32Pressure sensor calibration problem.E35Pressure sensor indicates water overfill.1. Is the water level above 4.5 inches?Yes. Go to step (2).No. Go to step (4).2.
Does water enter the washer continuously?Yes. Go to step (3).No. Check Air Trap for clog, if not replace the main control board.3. Remove power from washer.Does the water stop coming in?No. Replace the water valve assembly.Yes.
Check wiring to valve assembly for shorts. Ifwiring is good, replace the main control board.4. Replace the pressure sensor switch.Did this correct the problem?Yes. Problem solved.No. Replace the main control boardE38Air trap clogged.E41Control board thinks the door switch is open.1. Is the loading door closed?No. Close the door.Yes.
Go the step (2).2. Can you hear the lock attempt to close?Yes. Check the door strike. If good, replace the door switch.No. Go the step (3)3. Check wire connection between door lockand main control boardIf good, replace the door lock.
If problem is not corrected, replace the main control board.E42Door lock device failureE44Door closed sensing failure.E45Line door sensing failure.E46Door command sense.E49Door incongruence between door line and door sense.E52Bad signal from tachogenerator.1. Disconnect the plug from the drive motor and measure the resistance pins 4 & 5 in the motor.If the reading is between 105 & 130 Ohms, replace the motor control board. If the meter reads other than between 105 & 130 Ohms, replace the motor.E53Low Voltage to Motor Control Board.1. Check wiring between the main control board and motor control board.If good, replace the motor control board.E54Over speed.1. Remove belt from the motor and spin the motor pulley. Does the motor spin free?No.
Replace the motor.Yes. Go to step (2)2.
Spin the tub pulley. Does the tub spin free?No. Check the tub bearings.Yes. Go to step (3)3. Disconnect the plug from the drive motor and measure resistance between pins 4 & 5 in the motor.If meter reads other than between 105 & 130 Ohms, replace the motor.
If reading is between 105 & 130 Ohms, Go to step (4)4. Disconnect plug from the motor and measure the resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 3 and 6 Ohms.If the readings are correct, replace motor control board. If the readings are incorrect, replace motor.E55Under speed.E57High current on inverter1. Find out if unit was overloaded. If not, remove belt from the motor and spin the motor pulley.
Does the motor spin free?No. Replace the motor.Yes.
Go to step (2)2. Spin the tub pulley. Does the tub spin free?No. Check the tub bearings.Yes. Go to step (3)3.
Disconnect plug from the motor and measure resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 3 and 6 Ohms.If readings are correct, check wiring from motor to motor control board, If good, replace motor control board. If the readings are incorrect, replace motor.E58High current on motor phase.E59No tachogenerator signal for 3 seconds.See E54See E54E5AHigh temperature on heat sink caused by overloading.See E57See E57E5CHigh Voltage experienced by MC.1. Have power company check the frequency and voltage of the incoming power.If correct, for error code E5C, replace motor control board. If correct, for error codes EA1, EA2, EA3, EAE or EA5, replace main control boardE5DCommunication problem.1. Communication problem. Check the wiring between the main control board and the motor control board.Wiring bad, correct wiring problem.Wiring good, replace main control board.
If problem is not corrected,replace the motor control board.E5ECommunication problem.E5FMC is continuously resetting.E67Heater sensing relay failure.1. Check the resistance of the heating element. It should be approximately 14 ohms.If readings are incorrect, replace heating element.2. Check the resistance between ground and both heater terminals.
It should be open when heater terminals are disconnected.If readings are incorrect, replace the heating element. If problem is not corrected, replace main control board.E68Current leakage to ground on heater or fuse opened.E69Heating element relay failure.E71Drum water NTC failure. (Tub heater)1.
Check the resistance of the drum water NTC.Is it around 4.8K ohms?No, replace the heating element.Yes, check the wiringE74Wash temperature does not increase.See E71See E71E91Communication error between UI board and main control board.1. Communication problem. Check wiring between the main control board and user interface board.Wiring bad, Correct wiring problem. Wiring good, Replace the user interface board. Electrolux ENV series washer error codesENV06 is among the most popular washers from the Electrolux ENV line. The front loader produced by the company’s Swedish division Distiparts uses the same platform as the EWM1000, EWM2000evo, and EWM3000ne washing machines.